亚克力镜比玻璃镜有很多优点。 重量仅为 1/2，断裂次数多出许多倍
抵抗的。 它可以轻松切割或成型以适合框架。 从外观上看，亚克力镜没有什么区别
从玻璃。 但是，它必须正确安装。
由于亚克力镜具有一定的柔韧性，因此它可以及时顺应物体的不规则形状。
支撑面。 不光滑、非平面的表面会导致镜像的局部弯曲
片材和反射图像的畸变。 视觉失真也是观看距离的函数
材料厚度。 较厚的丙烯酸树脂的柔韧性较差，因此可以保持更好的光学完整性。
正确的安装和足够的材料厚度可以减少视觉失真，但可能不会
彻底消除它。
为了获得最佳效果，镜面板应安装在光滑、坚硬、坚固的平坦背衬上，例如 5/8”
或 3/4” MDF、中密度纤维板或同等平坦的表面。 表面应清洁、干燥、自由
任何剥落或粉状油漆。
不建议采用天花板和架空安装，除非镜面亚克力安装在
边缘接合框架，例如 T 形吊顶框架或机械安装。
镜面亚克力的背面涂有反射膜。 然后涂上油漆进行保护
反射面。 仅使用专为丙烯酸镜子设计的粘合剂。 向 TAP 销售人员询问
推荐的粘合剂。 有些粘合剂可能含有甲苯、酮和己烷等溶剂
可以攻击镜子的背面涂层。 不推荐使用溶剂含量为5%或更多的粘合剂。
由于有多种粘合剂、水泥和胶粘剂可供使用，因此应在消耗性材料上对它们进行测试
应用前的碎片。 所有测试应至少提前 72 小时进行，以确定
与背涂层、反射涂层和丙烯酸本身的兼容性。 亚克力镜子带有背胶
用于亚克力镜子。 详情请咨询您的销售人员或访问我们的网站：www.aulen.cn。
从距边缘约 3 英寸处开始，以 5-6 英寸间隔的垂直珠子涂抹粘合剂。 安装镜子10以内
涂抹粘合剂的分钟数。 以机械方式支撑镜子（镜夹等）直至粘合剂干燥。 做
如果温度低于 60° F，请勿涂抹粘合剂。仔细阅读并遵循粘合剂说明。 干净的
镜子用超细纤维布和肥皂水、塑料清洁剂。
我们再次强调，在使用任何粘合剂、水泥或胶粘剂之前，请测试消耗性样品
至少 72 小时以确定是否适合。
访问我们的网站：www.aulen.cn

Acrylic mirror has many advantages over glass. It is 1/2 the weight and many times more break
resistant. It can be easily cut or shaped to fit a frame. In appearance, acrylic mirror is indistinguishable
from glass. But, it must be mounted properly.
Since the acrylic mirror is somewhat flexible, it can, in time, conform to the irregularities of the
supporting surface. A non-smooth, non-planar surface will cause localized bending of the mirrored
sheet and distortion in the reflected image. Visual distortion is also a function of viewing distance and
material thickness. Thicker acrylic is less flexible and therefore maintains better optical integrity.
Correct installation and sufficient material thickness can reduce visual distortion but MAY NOT
COMPLETELY ELIMINATE IT.
For best results, mirrored sheets should be mounted to a smooth, rigid, sturdy flat backing such as 5/8”
or 3/4” MDF, medium-density fibre board, or equally flat surface. Surface should be clean, dry and free
of any flaking or powdery paint.
Ceiling and overhead installations are not recommended unless the mirrored acrylic is mounted in
edge-engaging frames such as T-bar suspended ceiling frames or mechanical mounting.
Mirrored acrylic has a reflective film applied to backside of the acrylic. Paint is then applied to protect
the reflective surface. Use only adhesives designed for acrylic mirror. Ask a TAP salesperson for the
recommended adhesive. Some adhesives may contain solvents such as toluene, ketones and hexane
that can attack the mirror’s backcoat. Adhesives with solvents of 5% or more are not recommended.
Since numerous adhesives, cements, and mastics are available, they should be tested on expendable
pieces prior to application. All tests should be applied at least 72 hours in advance to determine
compatibility to the backcoat, the reflective coating and the acrylic itself. acrylic mirror carries adhesive
for acrylic mirror. Ask your salesperson for details or find it on our website: www.aulen.cn.
Apply adhesive in vertical beads 5-6” apart, starting about 3” from the edge. Mount mirror within 10
minutes of applying adhesive. Support mirror mechanically (mirror clips, etc.) until adhesive dries. Do
not apply adhesive if temperature is below 60º F. Read and follow adhesive instructions carefully. Clean
mirror with a micro fiber cloth and soapy water, Plastic Cleaners.
Again we stress, before using any adhesives, cements, or mastics, please test expendable samples
for at least 72 hours to determine suitability.
Visit our website: www.aulen.cn